PCB Surface Finish
- Home
- PCB Surface Finish
What is a PCB surface finish?
A PCB surface finish is a thin protective layer applied to the exposed copper pads and traces of a finished board. It stops copper from oxidizing and keeps every pad ready for soldering.
Solderability
The finish decides how reliably pads wet during assembly, which drives yield.
Flatness
A planar surface is required for fine-pitch parts and BGAs under 0.5 mm.
Shelf life
How long a board can sit in storage before assembly without losing solderability.
Cost
Finish choice moves unit cost and assembly yield at the same time.
Surface finish types at a glance
Seven common finishes, compared on what they are, what they are good at, and where they fall short.
| Finish | What it is | Strength | Watch out for | Best for |
| Electroplated Nickel Gold | Nickel under a thick hard gold layer, electroplated. | Wear-resistant contact surfaces. | Highest cost; not for general soldering. | Edge connectors, contact fingers. |
| HASL (leaded) | Hot-air solder leveling with tin-lead. | Lowest cost, most forgiving solderability. | Non-flat surface; contains lead. | Through-hole, large-pitch SMT. |
| Lead-Free HASL | Hot-air leveling with a lead-free SAC alloy. | RoHS-compliant, excellent solderability. | Higher reflow temperature; non-flat. | Consumer electronics, lead-free builds. |
| OSP | Organic preservative layer on bare copper. | Very low cost, flat, RoHS-compliant. | Short shelf life (3–6 months). | High-volume, short-cycle boards. |
| ENIG | Electroless nickel + immersion gold. | Flat, excellent solderability, 12-month shelf life. | Black-pad risk; higher cost. | Fine-pitch BGA/QFN, keypads. |
| Immersion Silver | Thin silver layer deposited on copper. | Flat, good solderability, RoHS-compliant. | Tarnish and silver-migration risk. | RF boards, fine pitch on a budget. |
| Immersion Tin | Thin tin layer deposited on copper. | Flat, good solderability, RoHS-compliant. | Tin-whisker risk; short shelf life. | Press-fit, fine-pitch boards. |
Typical industry data — confirm thickness ranges and standards (e.g. IPC-4552 for ENIG) with your manufacturer.
Lead-free or leaded?
Regulation decides most of this question. Here is the rule in two lines.
Lead-free — the default
Required for RoHS/REACH-compliant products and standard in commercial electronics. Nearly all modern production runs lead-free.
- Lead-Free HASL, ENIG, OSP, Immersion Silver, Immersion Tin
- Compliant across consumer, industrial and most automotive programs
Leaded — the exception
Allowed only under regulatory exemptions, mostly military, aerospace and legacy programs that still specify it.
- Leaded HASL offers the most forgiving soldering window
- Choose it only with a valid exemption in place
Bottom line
Unless your program holds a specific exemption, choose a lead-free finish.
Cost vs. solderability: where each finish sits
The first trade-off engineers ask about. Solderability is plotted against relative cost — higher is better on both axes.

Typical industry positioning — exact values vary by supplier, volume and stack-up.
Read it this way: HASL gives the most solderability per dollar but poor flatness. OSP and immersion tin or silver buy flatness cheaply but give up shelf life. ENIG is the balanced pick. Hard gold exists for contacts, not soldering.
How to choose a surface finish type
Is RoHS compliance required?
Go lead-free: Lead-Free HASL, ENIG, OSP, Immersion Silver or Tin. Choose leaded HASL only with a valid exemption.
Fine-pitch parts or BGAs under 0.5 mm?
You need a flat finish: ENIG, OSP, Immersion Silver or Immersion Tin. HASL is not flat enough.
Fine-pitch parts or BGAs under 0.5 mm?
ENIG supports aluminium wire bonding. Hard gold is for contact fingers and wear surfaces.
How long will boards sit in storage?
Long shelf life (12+ months) points to ENIG. Short JIT cycles make OSP the cost saver.
What is the cost target?
Lowest: OSP or HASL. Balanced: ENIG. High reliability or contacts: ENIG or hard gold.
One-line rule: Flat, fine-pitch and long shelf life → ENIG · Lowest cost → HASL or OSP · Contacts and wear → hard gold
PCB Types
Certifications
PCB Surface Finish
- Inside this flex PCB: how it fixes wiring, hinge and connector failures
- When a fraction of a millimetre decides whether the board fits
- How Much Does a PCB Cost? The 10 Factors Behind Your Circuit Board Price
- Thin Core PCB Manufacturer: 0.6mm Green Solder Mask & Gold Plating
- The Audio Capacitor Guide: Crossovers, Car Audio & Subwoofers